Like most people, you probably don’t think about your dishwasher until it stops working correctly. And when that happens, it can be frustrating and time-consuming to figure out what’s going on. That’s where Samsung dishwasher error codes come in. But what are the error codes for Samsung dishwashers?
The most common Samsung dishwasher error codes are as follows:
- 1E or IE—Clogged filter error
- PC—Zone wash error
- LE or LC—Leakage error
- 3C—Pump operation error
- bE or 6E—Stuck button error
- 3E—High water temperature error
- 5C, SC, 5E, or SE—Drain error
Knowing what the error codes are is only half the battle. In this guide, we will learn what these error codes mean and how to resolve them. I’ll also cover some of the less-common error codes.
What Are Samsung Dishwasher Error Codes?
Samsung dishwasher error codes are alphanumeric codes that appear on the display panel when there is an issue with the dishwasher. These codes can help identify the specific problem and allow for easier troubleshooting.
When an error code appears, it is crucial to consult the user manual or contact a professional for assistance in resolving the issue. Ignoring an error code may result in further damage to the dishwasher or even cause safety hazards.
Common Samsung Dishwasher Error Codes
Now, let’s get into the meat and potatoes of the matter—what these error codes mean. I mentioned some of the more common error codes that appear, but in this section, I’ll explain what causes them to appear and how to resolve the problem.
1E or IE
The 1E or IE error code in Samsung dishwashers can be caused by a clogged filter in the water inlet valve. Over time, minerals and debris from the water supply can accumulate in the filter, reducing water flow and causing the dishwasher to display the error code.
To resolve the issue, the filter must be cleaned thoroughly. The first step is to locate the filter assembly at the bottom of the dishwasher and carefully turn the handle counterclockwise to remove the filter door. The micro-filter can then be removed and rinsed under running water to remove debris. It’s important to remove all waste from the filter and to clean the filter regularly to prevent further clogging.
PC
The PC error code in Samsung dishwashers indicates a problem with the Zone Wash function. This feature allows the user to select specific zones within the dishwasher for more targeted cleaning. If you encounter this error, check the spray arm and water distribution system for blockages or damage.
To do this, remove the spray arm and check for any clogs or cracks. Then, inspect the water distribution system for any loose connections or blockages. It may also be necessary to prevent the control board for any software or hardware issues related to the Zone Wash function. By following these steps, you can fix the problem and get your dishwasher working properly again.
LE or LC
The Samsung dishwasher’s bE or 6E error code indicates a stuck button error. This error may occur when a button on the dishwasher’s control panel is stuck or pressed continuously, preventing the dishwasher from operating properly.
To fix the issue, it is recommended to check the door gasket for any damage or debris preventing a proper seal. Checking the hoses and valves for leaks or damage is also recommended. In some cases, it may be necessary to replace the dishwasher tub if it is damaged or cracked. It is important to address the leakage issue promptly to prevent further damage to the dishwasher or surrounding area.
3C
The 3C error code in Samsung dishwashers can also indicate a pump operation failure. This error may occur due to a faulty motor, a damaged impeller, or a clogged drain pump. The dishwasher may detect a problem with the pump and activate the error code to prevent further damage or flooding.
To fix the issue, checking the drain pump for any clogs or debris that may be preventing proper operation is recommended. It is also recommended to check the motor and impeller for any damage or wear that may be preventing the pump from functioning properly. In some cases, replacing the pump or motor may be necessary to resolve the issue.
bE or 6E
The bE or 6E error code in Samsung dishwashers indicates a stuck button error. If a button on the dishwasher’s control panel is stuck or pressed continuously, it can cause an error and stop the dishwasher from working properly.
To fix the issue, it is recommended to inspect the control panel and check for any buttons that may be stuck or damaged. In some cases, it may be necessary to replace the control panel to resolve the issue. It is important to avoid using excessive force when pressing buttons on the control panel to prevent them from becoming stuck in the first place.
3E
The 3E error code in Samsung dishwashers indicates a high-temperature water supply error. This error may occur when the dishwasher’s temperature sensor is not sending proper readings to the control board, causing it to think that the water in the dishwasher is too hot. The error may also occur if the temperature sensor is dirty and requires cleaning.
To fix the issue, it is recommended to check the dishwasher’s temperature sensor and ensure that it is functioning properly. The sensor can be cleaned with a soft cloth and mild soap solution.
It is also recommended to check the dishwasher’s water supply and ensure that the water is not too hot or too cold. If the issue persists, it may require replacing the temperature sensor or seeking professional assistance to diagnose and fix the issue.
5C, SC, 5E, or SE
The 5C, SC, 5E, or SE error code in Samsung dishwashers indicates a drain error. This error may occur when the dishwasher is unable to drain properly due to a clogged or damaged drain hose, a clogged filter or pump, or a malfunctioning drain pump.
To fix the issue, it is recommended to check the dishwasher’s drain hose for any clogs or damage and ensure that it is properly connected to the drain system. It is also recommended to check the dishwasher’s filter and pump for any clogs or debris that may be preventing proper drainage. In some cases, it may be necessary to replace the drain pump or seek professional assistance to diagnose and fix the issue.
Other Samsung Dishwasher Error Codes
The official website for Samsung dishwashers lists other possible error codes that can appear. The following codes are not as common as the 7 listed above, but they deserve just as much attention if they pop up on the dishwasher’s display.
4C or 4E
The 4C and 4E error codes in Samsung dishwashers indicate that the dishwasher is not receiving water at the appropriate pressure or temperature.
To resolve the issue, check the water pressure and temperature to ensure they meet the dishwasher’s requirements, avoid using Floodsafe hoses as they are incompatible with Samsung dishwashers, and make sure the water supply is turned on.
7E
The 7E error code in Samsung dishwashers indicates a Waterwall reflector error, where the reflector is not able to move correctly. To resolve the issue, check if any packing tape on the reflector needs to be removed, ensuring that it is installed in the correct position and is not blocked.
9E
The 9E error code in Samsung dishwashers indicates a low water level error, with insufficient water in the dishwasher. To resolve the issue, empty the dishwasher, add detergent, and then run a normal cycle.
AP
The AP error code in Samsung dishwashers means the dishwasher is in Access Point Mode to facilitate connection to a mobile device. If this is not the intention, the user can resolve the error by turning the dishwasher off and back on.
HC, 1E, or IE
The HC, 1E, or IE error code in Samsung dishwashers indicates a high-temperature heater error, where the temperature inside the dishwasher is too hot. To resolve the issue, switch off the power to the dishwasher for 30 seconds and turn it back on at the circuit breaker. Empty the dishwasher, fill the detergent drawer, and then start a Normal cycle.
HE
The HE error code in Samsung dishwashers indicates that the temperature inside the dishwasher is detected incorrectly. To address the issue, empty the dishwasher, add detergent, and run a normal cycle.
OC, 0C, or oE
The OC, 0C, or oE error codes in Samsung dishwashers indicate an over-level water error, often related to a drain issue. To address the issue, inspect the dishwasher’s drain connection at the sink, check the drain hose, run water in the sink connected to the dishwasher, and clean the drain, filter, and sump in the tub.
PE
The PE error code in Samsung dishwashers indicates a Half Load function error, where the half-load function is not performing correctly. To resolve the issue, empty the dishwasher, add detergent and run a half-load cycle.
tE
The tE error code in Samsung dishwashers indicates a temperature sensor error, where the temperature inside the dishwasher is being detected incorrectly. To address the issue, empty the dishwasher, add detergent, and run a normal cycle.
Leave a Reply